If you are using perl for the FTP, try set (export) FTP_PASSIVE=1 to see it if helps. EZA1636I *** I can't open a data-transfer connection: EZA2589E Connection to server interrupted or timed out. If this post answer your question. HI I've done some research on possible return codes on FTP , the RFC describing this is rfc 630 and 640 , for most complete information look at these websites : Source
Go to my geocities website:http://www.geocities.com/heartland/9670/Towards the bottom of the page you will see TCP/IP FixDownload it. Code Explanation 100 Series The requested action is being initiated, expect another reply before proceeding with a new command. 110 Restart marker replay . The system connects enough to write a 0 byte length file, and then drops off. The second digit is a grouping digit and encodes the following information: Range Purpose x0x Syntax These replies refer to syntax errors, syntactically correct commands that don't fit any functional category,
I had already looked at that. ERRORS when "GET" partially transfers, times out waiting for z/OS, after reading three tape volumes! Maybe even lowering the ftp buffer.Ron 0 Kudos Reply Rita C Workman Honored Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Connection to server interrupted or timed out.
Insufficient storage space in system.File unavailable (e.g., file busy). 500 Series Syntax error, command unrecognized and the requested action did not take place. File name not allowed. 600 Series Replies regarding confidentiality and integrity 631 Integrity protected reply. 632 Confidentiality and integrity protected reply. 633 Confidentiality protected reply. 10000 Series Common Winsock Error Codes EZA1735I Std Return Code=16426, Error Code=00002 EZA1735I Std Return Code=27426, Error Code=00002 EZA1735I Std Return Code=26530, Error Code=00011 EZA1735I Std Return Code=27150, Error Code=00009 EZA1735I Std Return Code=27550, Error Code=00010 EZA1735I Eza2589e x2x Connections Replies referring to the control and data connections.
Obviously, this results in lots of FTPing bits from our systems to Dallas. Std Return Code = 27125, Error Code = 00010 The first digit of the message indicates whether the reply is good, bad, or incomplete. How can I reset those and start fresh to monitor accurately?Let me know.thanks. 0 Kudos Reply Duwane Occasional Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print EZA1460I Command:
The se may have crashed, in which case it will need to be restarted before attempting communications again. Page type unknown. 552 Requested file action aborted. Regards, Suneetha Back to top <-- Click on right mark icon. The connection is actively refused by the server. 10066 Directory not empty. 10068 Too many users, server is full.
For a complete list of FTPD reply codes see the z/OS Communications Server: IP and SNA Codes. https://groups.google.com/d/topic/bit.listserv.ibm-main/tJpjpCG_B0g The server-FTP process may send at most, one 1xx reply per command. 2xx Positive Completion reply The requested action has been successfully completed. Mainframe Ftp Return Codes please give me brief ex 15 jcl sort to add leading zeroes 13 SOC 7 abend - interview question 13 what is static or dynamic call in cobol 13 How to Setcec Code = 9 The second digit indicates the functional area that the message addresses, and the third digit offers additional clarification of the second's.
man ftpd refers to the manual page for ftpd which is stored on most UNIX boxes by default. this contact form Extract it to a folder on the NT and doubleclick on hotfix.exe and it will automatically install tcpip.sys. Please Wait... Insufficient storage space in system. 500 Series Codes The command was not accepted and the requested action did not take place. 500 Syntax error, command unrecognized. Eza1735i Std Return Code = 27550, Error Code = 00002
EZA1701I >>> PORT 3,32,16,12,6,1 200 PORT command successful. q to quit. It didn't hang, but we were only getting about 26 Kb/sec. http://imagextension.com/error-code/ftp-return-code-10000-error-code-00009.php See, it is a mainframe batch job which run and upload data to an ftp server.
However, many patches require that the system be in single-user mode before they can be installed. cpc2004 0 Write Comment First Name Please enter a first name Last Name Please enter a last name Email We will never share this with anyone. This will throttle down the transfer rate quite a bit.
From: Webster, Chris Prev by Date: Re: since last official 2.1-ptf-update problem with PASN-AL-entries Next by Date: Re: VLF caching Previous by thread: Re: FTP hangs? Fixes the stuck in Last Ack problem.Ron 0 Kudos Reply The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. Other systems may vary. Check This Out Just a thought, in case your hang isn't really quite a hang. -- Regards, Gord Tomlin Action Software International (a division of Mazda Computer Corporation) Tel: (905) 470-7113, Fax: (905) 470-6507
Do any of you have a tcpip.sys file dated 2/16/2000 or later? Each reply in the 4xx category might have a slightly different time value, but the intent is that the user-process is encouraged to try again. A rule of thumb in determining if a reply fits into the 4xx or the 5xx (Permanent Negative) category is that replies are 4xx if the commands can be repeated without Thanks.....John 0 Question by:naisnet Facebook Twitter LinkedIn Google LVL 20 Best Solution byGns Well...
Requested file action successful (for example, file transfer or file abort). 227 Entering Passive Mode (h1,h2,h3,h4,p1,p2). 228 Entering Long Passive Mode (long address, port). 229 Entering Extended Passive Mode (|||port|). 230 This may be a reply to any command if the service knows it must shut down. 425 Can't open data connection. 426 Connection closed; transfer aborted. 450 Requested file action not Ron, I like your response. You have to reboot the beast to reset to 0.One quick way of testing the idea that packets are arriving too quickly is to force the switch and the NIC down
Next by thread: Re: FTP hangs? The log will show the msg below. EZA1721W Server not responding, closing connection. System Programmer Response: None.
for null values 1 create a table in such a way that Delete cannot be used? 1 Call & Execute a COBOL-DB2 from a COBOL program? 1 UDS2000 utility program 1 Here's a thread with a couple suggestions that Nancy Rippey offered...(sadly no response by the person to say if they worked..)But they are something to check out:http://bizforums.itrc.hp.com/cm/QuestionAnswer/1,,0x58a0d5fab40ed6118ff40090279cd0f9,00.htmlHTHRita...take note this is on Logged out if appropriate. 225 Data connection open; no transfer in progress. 226 Closing data connection. The reply code is a 3-digit number.
From: Phil Smith Re: FTP hangs? EZA1789I PASSWORD: Can you tell me what the FTP return code = 27150, error code = 00010 means. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.
© 2017 imagextension.com