Home > Error Code > Ge Electric Convection Oven Error Codes

Ge Electric Convection Oven Error Codes

Contents

C2 - Drain Line Totally Blocked - This error will occur when dishwasher is unable to pump out water within the maximum time of 405 seconds. Check probe. Find Parts ^ top GE Microwave Fault Codes Failure Code Fault Code Description Solution F1 Oven cavity thermistor open Check oven thermistor for continuity. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both. http://imagextension.com/error-code/ge-electric-wall-oven-error-codes.php

On some models the keypad and the control board are made together, if so replace control. F3 or F4 Open or shorted oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Check wiring and test operation of switches. Transkript Das interaktive Transkript konnte nicht geladen werden.

Ge Profile Oven Error Codes

Check sensor, sensor harness and sensor harness connection at sensor and oven control. Make sure the control panel ribbon cable is plugged into the control board slot tight and firm. Anmelden Wird geladen... If found defective, replace sensor.

Find Parts ^ top Appliance Repair Appliance Repair Dishwasher Repair Garbage Disposer Repair Dryer Repair Freezer Repair Microwave Repair Range / Oven Repair Range Hood Repair Refrigerator Repair Trash Compactor Repair This study will take approximately 30 to 45 minutes of your time, and can be conducted around your schedule. Leslie // Apr 4, 2015 at 3:40 pm Thanks for sharing, I'm going to try and fix it right now!! Ge Error Codes Washer If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit.

One question: why did you push and hold the bake button? If not, you need to figure out which one to change. Turn off household water supply to washer and unplug power cord. · Check wiring harness · Check water inlet valve · Check pressure sensor switch · Check circuit board GE Microwave F1 Stuck touch pad Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced.

Appliance parts online, right part, best price and fast shipping. Ge Oven Error Codes F7 E6 Donate to let this website help you next time! Each function or operation has a numerical value assigned to it. If shorted, look for pinched or cut wire in oven temperature sensor circuit.Check connector terminals - Look for deformed or corrosion on terminals.

Ge Oven Error Codes F2

F2 - Oven Cavity Thermistor Closed - Check oven thermistor for continuity and replace if zero or infinite ohms. http://www.appliance-repair-it.com/fault-code.html The control board is bad and needs replacing. Ge Profile Oven Error Codes Notify me of new posts by email. Ge Oven Error Codes F3 Switch is normally closed and will open if area overheats due to fan not operating.

If so, its grounded out and replace sensor and/or sensor wires, if its not grounded out replace control board. have a peek at these guys On some models you also have to remove the screw which attaches the ground wire to the control panel. Tags: Oven error codes 22 responses so far ↓ Andrew Smith // May 12, 2009 at 3:03 am Your repair instructions for Fault code F7 on our GE oven were perfect. F6 This fault code stands for shorted start key. Ge Oven F9 Error

Wird verarbeitet... E - Drain Pump Error - Press 'Power' button and check wiring harness, pump motor, and circuit board for defects. Check the probe for pinched wires and make sure there is no condensation or contamination on receptacle. check over here If the resistance is not within that range replace the sensor.

Press POWER button. F76 Ge Oven If wiring is ok, replace control board (clock). Melde dich bei YouTube an, damit dein Feedback gezählt wird.

Pushing CLEAR/OFF pad. 2.

Looks like the control panel/membrane assembly would need to be replaced. F8 EEPROM data error. If you would like to schedule a service appointment, please contact GE Appliance Service at 1-800-432-2737 or schedule a service appointment onlineGE Appliances does recommend turning the range or oven off Ge Oven Error Code F7 No other buttons work: · Check wiring harness · Check water valve· Check pressure sensor switch · Check circuit board E - Drain pump error Water level does not decrease to

Look for cause - fan thermal switch not closing, fan stalled, etc.Look for high resistance in the oven temperature sensor circuit due to high contact resistance (poor terminal crimp, deformed terminals, Find your part: Appliance parts online, right part, best price and fast shipping. If within that day the code comes back, replace control if the code doesn’t come back, replace keypad. http://imagextension.com/error-code/ge-profile-convection-oven-f7-error.php Whether you can replace the keypad instead of the control board and keypad, I don’t know.For something that complicated, I’m calling for service.F7 is the error for a shorted function key.

F3 or F4 Open or shorted oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Determine if problem is with the Key Panel or Control by: 1. The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd. Bitte versuche es später erneut.

Gene. If the resistance is not within the range mentioned above, then replace the sensor. Click here for more information on other GE Parts from PartSelect.com Back to top Tweet PartSelect.com Home Contact About Us Help Privacy Policy Terms of Use Just For Fun!

© 2017 imagextension.com