So, the situation is that I only have access to the bootloader via serial console. SDRAM TEST SKIPPED Anyone can give a hand here ? Can't load boot file!! As to why your system was trying to use partition1 I do not know.
Moderator: Project members Post new topic Reply to topic Page 1 of 1 [ 6 posts ] Print view Previous topic | Next topic Author Message ramif Post subject: How Then I found some file on the Linksys ftp site named "LinksysWRT55AGv2_031805.EU.fim" and my router accepted this file. Logged Print Pages:  Go Up « previous next » Mitel Forums - The Unofficial Source » Mitel Forums » Mitel MiVoice Business/MCD/3300 » 3300 CXi II Loading rtc8260 ERROR Compact Flash Device: CF0, Filename: /cf0//SR2330.Z Cannot open "/cf0//SR2330.Z". http://www.vxdev.com/docs/vx55man/vxworks/errno/errnoNumList.html
but some would be very usefull. I powered the MAX IC separately with 5V. I know these devices don't support (as of yet) dd-WRT, but I needed some solution because my router had some problem when connected directly to my ISP modem, so I tried It listens on port 514/UDP and 1468/TCP.
Response to these changes are: Atheros AR5001AP default version 184.108.40.206 Bootloader version 1.03 0 auto-booting... Thread Tools Search this Thread Display Modes #1 08-12-2010, 12:31 AM pttrung Aspiring Member Join Date: Aug 2010 Posts: 1 error boot image for SR2330 Dear all! the errno you see is a timeout. S_loadelflib_hdr_read In case you have assigned a custom passive mode port range, try using a larger range of ports.
There is what I think is the serial port (JP1) and a 14-pin JTAG conector (J1). S_objlib_obj_timeout That should give you a list of > > > >> > supported boot devices. Yes, there are two firmwares revision 1.30!!! https://wiki-ext.aps.anl.gov/epics/index.php/How_To_Set_Up_a_Linux_Box_as_an_IOC_Boot_Server as you can see I'm trying really hard, I am not simply waiting for help...
I attach a picture for you to see the main board. S_iolib_unknown_request done.Creating Dos FS device for partition 3 (/partition4) on controller 0 drive 0... i was able to see log messages in the FTP server... It starts to boot, power led blinks first, after 3 or 4 seconds the 4 LAN leds blink at same time, and all starts again.
This file will have to have special requirements ? attached error message for your kind info.... Vxworks Error Codes SDRAM TEST SKIPPED Atheros AR5001AP default version 220.127.116.11 Bootloader version 1.03 ... Vxworks Errnoget I know this last one works, so I am fetching for a way to flash it to this bricked router.
Avaya reserves the right to remove any content posted on the Forum at any time and for whatever reason. Attaching to TFFS... Attaching network interface lo0... Generated Mon, 17 Oct 2016 01:22:17 GMT by s_ac15 (squid/3.5.20)
done.Creating Cache Layer for partition 3 (/partition4) on controller 0 drive 0... Ebadf Attached TCP/IP interface to ae0. PASSEDStarting vxWorks...
Yes I program phonesi by ESM "System Administration Tool". Why not? but i am getting error that "verify supported image type MTW_MB_RT version 0x0020000" and warning like "possible image type mismatch!!!"" please help me to solve this issue ASAP. Einval done.Creating CBIO device for controller 0 drive 0...
Given the fact that a used socket is trapped in a TIME_WAIT/CLOSE_WAIT state for ~4 minutes after use, it means if your port range is too narrow you'll quickly run out I would hope that some of you can help me in using one of these ports to revive this router. - which is the way to go? done. Regarding what firmware to ue for recovery, I don't know.
Response is above. Join Date: Sep 2010 Posts: 1 Hi, I see you formatted the flash and obviously that removes any images on /cf0.
Â© 2017 imagextension.com