Home > Fuser Error > Fuser Error 50.3

Fuser Error 50.3

First Time Here? The trailing edge of the paper may be visible and it can be gently teased out and peeled away. Control of the fuser is therefore spread across the fuser itself, the DC-Controller and the power supply board. Control breakdown is difficult. http://imagextension.com/fuser-error/fuser-50-2-error.php

However, before jumping to the conclusion that the fuser has gone wrong - or the power supply is overwhelming the printer, some other checks will help. twitter for FW printer repair. Somewhere in their list of instructions on the "50.3" error everyone says something along the lines of "remove, inspect and reseat the fuser". This is known as offsetting; the ghost print is at intervals of 94 mm which is the circumference of the fuser sleeve. http://printerrepairsupport.com/50-3-fuser-error-hp-p4015-p4015-p4515/

Do not let the link arm snap back toward the product when you release it. 4. Many UPS's will report the line voltage, so a report from one of those near the printer can help. (No, the printer doesn't need plugging into it, the UPS and printer fixya The usual mixed bag of irrelevances with one mention of 50.3 and no solution.

HP P4014, 4015, 4515 Fusing Assembly RM1-4554 CB506-67901 Troubleshooting the 50.3 Fuser  Error in the HP Laserjet  P4014, P4015, P4510 PrinterGiven the 50.3 fuser error is a high temperature error the The DC controller is told what temperature to reach by commands from the control panel, or from the formatter (which gets them over the network from the driver in the user's There is no circuit diagram. If the printer has been moved from a cold to a hot room (or from a warm place to a cool one) then the environment thermistor will be wrong and the

The most likely point of failure is on the power-supply board. I thought nobody had said anything! :) The fuser I installed was aftermarket and I don't recall what I did to fix it, but it's working fine so I guess I As the fusing assembly is already overheating turning it back on right away can cause it to heat up more and permanently damage the unit. http://printerrepairsupport.com/50-3-fuser-error-on-the-hp-p3015/ If the problem persists another point to check might be the printer driver fuser setting.

The heater is what fails and gives the error, so you don't have to replace the whole expensive fuser or maintenance kit. DO NOT merely turn the printer off and on again, there is a risk that a second dose of power will push the fuser to the point where the fuser cutout It could be expensive to fix. Bad Voltage.

Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting Overheated Fuser Before looking at the cause of a 50.3 error it might be an idea to see why it matters.   Signs of an over-hot fuser before an error happens Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, If the fuser innards are becoming too hot why does the DC controller feedback circuit not reduce power to the fuser until the flow of paper (or air from the four

Respond to this 1 If you want to save a few bucks, I can supply you with just the heater portion of the fuser and an instructional video to replace it. http://imagextension.com/fuser-error/fuser-error-50-9.php The thermistor circuit could fail. Very dry paper may not work in a laser printer anyway, the electrostatic transfer characteristics would be odd. Extension leads won't cause high voltage; nor will most possible failure modes in the fuser heater.

or its affiliates. by moe on Nov 23, 2014 at 11:29am Add comment Please sign in to comment Please sign in to comment HP LaserJet 4050 Buy discount ink Buy this printer More HP Bad frequency or power factor. Check This Out Kevin For More information involving Printer Repair and some articles I have written check out: http://blog.marketpoint.com/ Related posts:HP 4300 Laserjet 50.3 Fuser Error For High Temperature 50.1 Fuser Error in the

Fuser power switching circuits require something between 45 and 65 hertz and sine wave to work correctly. Any error codes the might get stuck insides the machines memory will have a chance to clear and upon start-up it will go through the normal warm up procedure. For instance, power switching semiconductors are generally intended to operate at the zero-volts point of the AC power cycle but if the power factor is bad that is not the zero

That is quite a significant effect.

Since exposed meter probes could deliver a fatal electric shock this should be left for an experienced technician if you have the slightest doubt about your own abilities. While not the most common error it still happens on occasion. If the fuser sleeve does not rotate properly then if media were to arrive print will smear. Quick Answers?

Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, The toner powder used in the LaserJet P4014 series printers is a mix of polyester and iron oxide specially chosen for its low melting point because that improves energy efficiency. Wrong settings. this contact form high temperature Solution: 1.

Fuser 1. Paper always contains some water - it is a hygroscopic material and will pick up moisture from the atmosphere if iis not hermetically sealed in a pack. Any advise will be appreciated. If the thermal cutout is raised above its rated temperature it interrupts the fuser power circuit, preventing a fire hazard.

It would need a supply rated at 3 kilowatts or more (about 4KVA) to guarantee a good supply to most laser printers. (The fuser is a resistive load, but it has Pull down on the rear-door assembly to remove it.

© 2017 imagextension.com