Home > Fuser Error > Fuser Error Elite 21

Fuser Error Elite 21

Action Turn the printer off. CloseFace-upbinface-upbin, or send job to standard bin.ErrorThe envelope feeder is not installed and has been selected.Envelope FeederInstall envelope feeder, or choose another paper source.Service requiredThe fusing unit is operating outside its Depending on operating conditions, however, the fuser may need to be replaced before or after that interval is reached. GCC Technologies Printers &... http://imagextension.com/fuser-error/fuser-50-2-error.php

Browse Categories Answer Questions Samsung ML-3561ND Laser Printer Samsung ML Printer and Copier Samsung Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters & They really do it. I found an eBay source for the thermistors - just search for N2125 thermistor. Im not trying to be mean or anything but thats my opinion.

Help this question get an answer by entering the correct category or product below. feederThe Envelope Feeder is not inserted. You may still have a defective fuser. The new one measures 1.1M ohms when cold.

Jul 12, 2011 | GCC Technologies Elite 12/600 Laser... 1 Answer 921 service Fuser error 921 Fuser Error indicates that the fuser unit failed to reach the standby temperature. Click "Add" to insert your video. Thanks for the help. - atlantis1 I have a problem with my printer xerox n2125. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.

no lamp, no spinning motor at power on, etc. Scroll to Check Others, press OK. See "Paper Jams," next section. 11-13 Previous page Next page 1...265266267268269 Also See for GCC Technologies Elite 21DN GCC Technologies 21 Series User Manual 275 pages GCC Technologies Elite 21DN https://h30434.www3.hp.com/t5/Inkjet-Printing/50-2F-00-fuser-error/td-p/5061105 Interestingly when I went to the electronics store to find the "right thermistor" or buy a resistor, the tech expert suggested the same thing: resistor in parallel.I bought and installed a

The information helped me repair a great printer at a very low cost. Operating System (including service pack revision) 3. Privacy Policy Terms of Use User Guides andService Manuals Manuals > GCC Printers > 21 Series > User Manual GCC Printers 21 Series User Manual Downloads: 0 Added: 12.09.2015 Size: 19.13 Any suggestions?

on-line value is 258.58 and i will sell for less. http://www.manualslib.com/manual/464109/Gcc-Technologies-Elite-21dn.html?page=267 after a few secs the printer will stop and again show the50.7 Fuser Error message.how do i fix this?please help! Toner requires the fuser to operate at a specific temperature range, too hot or too cold and it begins to stick to things it shouldn't and fall from things is should This gives the printer's engine board a chance to reset.

prev next 1 Points Related Questions: 1 Answer Fuser error printer 50.92.11 This indicates low fuser temperature. navigate here Insert the tray and the job will print.No env. so its a unit problem. HiMy N2125 gives me an "Fuser problem, power OFF" error.The heater should be OK, I suspect either the weird blue diode or the temp.

if fuser not getting hot, then suspect burned out fuser heater (look inside fuser roller for a long light bulb). Technician Reply 0 0 jimmyboy123 Student Posts: 1 Member Since: ‎07-24-2014 Message 10 of 16 (27,505 Views) Report Inappropriate Content Re: 50.7 Fuser Error Message Options Mark as New Bookmark Subscribe It was the thermal fuse that had blown.- Further reading on the net revealed that the fuse apparently gets worn down over time, and the higher resistance due to copper oxidation Check This Out Can you help?

The Fuser is held in place by 2 black thumb screws – remove these and pull the Fuser out. Paper Path Jams can be cleared as follows:1. It's problem with fuser.

Well, I have tried turning it off and back on.

Based on the error message, it could either be the fuser, or the system board. Include an image. Help this question get an answer by entering the correct category or product below. this would work: [cgi.ebay.com] or [search.ebay.com] who about getting several printers?

Plug the product directly into the wall socket. Close the cover.Load The printer requires the specified paper size in the specified trayto print the job. Replace the fuser.4. http://imagextension.com/fuser-error/fuser-error-50-5.php Usually caused when  one of the trays above has been removed.Toner is lowThe toner is low and will require replacement soon  (approximately 70 pages).Toner is emptyThe toner cartridge is empty.

Reply 0 0 pcwizard Provost Posts: 12,147 Member Since: ‎12-31-2009 Message 4 of 16 (37,150 Views) Report Inappropriate Content Re: 50.7 Fuser Error Message Options Mark as New Bookmark Subscribe Subscribe Games Applications Releases Articles Events Reviews Blogs Internet Communications Projects Entertainment Drivers the Entire site Home / Apps / How to hula hop How to hula hop Author: DODGEVIPER | 14.09.2014 by unknown on Sep 23, 2009 at 9:47am Add comment Please sign in to comment 0 Sometimes the fuser failure message appears just if your printer rises 200.000 printings, then before The display should come to “Ready” and the printer will be ready to resume printing. 10-12 Error/Status MessagesIn the event that a printer error occurs, the Elite 21 printer will display

It's been working perfectly ever since. If the error message goes away with the old fuser unit, please check that the new fuser unit is the correct one for this printer model. pick-up or buyer pay shipping.

© 2017 imagextension.com