Home > Groupwise Error > Groupwise Error 8909

Groupwise Error 8909

Click Post Office Links, select the post office, then click Edit Link. The system returned: (22) Invalid argument The remote host or network may be down. Action(s)Check the IP address for the POA. Action: Wait and try the operation again. http://imagextension.com/groupwise-error/groupwise-error-659.php

Ensure the UNC Path is correct7. Action: Stop some programs that are running on the server in order to free up some memory. See Using Client/Server Access to the Post Office in Post Office Agent in the GroupWise 2012 Administration Guide. See the following sections of the GroupWise 2012 Administration Guide, depending on which agent is encountering the problem: Securing the Post Office with SSL Connections to the POA in Post Office

Action: Make sure that the DNS name server is running. Error: 8908 Users are getting disconnected when trying to open GroupWise cause Packet receive buffers was set very low. ExplanationCannot write on connection; the receiver isn't responding. DNS is not loaded and you are trying to resolve DNS names.

Possible Cause: TCP/IP services couldn’t be used. Your cache administrator is webmaster. This is done by normally typing the "grpwise" command without quotes.If the issue still persists, please restart the server. Action: Finish configuring the agent for SSL.

Action: Obtain a new certificate file for one of the servers. Explanation: A GroupWise agent cannot establish an SSL connection because the handshake negotiation between the two servers failed. Action: Make sure that GMS is using port 8191. Possible Cause: Another program was temporarily using a very large amount of memory on the server.

Possible Cause: The other server is down. Possible Cause: If this error appears in the Message Transfer Status box of the POA, the MTA to which it is transferring messages is not running. Possible Cause: A client or server machine has crashed, or the process was forced to close without shutting down. If the MTA is restarting, the message transfer status should change to Open after the restart is completed. 8913 Cannot write on connection; timed out Source: GroupWise engine; TCP/IP communication.

See the Client Setup Guide. 8912 Cannot read on connection; timed out SourceGroupWise engine; TCP/IP communication. http://www.novell.com/support/kb/doc.php?id=7000974 Possible Cause(s)A client or server machine has crashed, or the process was forced to close without shutting down. The machine might have been exited while connections were active. See Use Client/Server Access to Post Office in Chapter 3: Reconfigure the POA in Book 2: Post Office Agent in the Agent Configuration Guide. 890B Cannot accept incoming connection SourceGroupWise engine;

Also, check the No ECB (Event control block) Available Count information in the LAN/WAN Information option in MONITOR.NLM. http://imagextension.com/groupwise-error/groupwise-error-601.php Explanation: Connection to the specified address failed. Generated Sat, 15 Oct 2016 20:09:03 GMT by s_ac5 (squid/3.5.20) Possible Cause(s)A client or server machine has crashed, or the process was forced to close without shutting down.

Possible Cause(s)TCP/IP services couldn't be used. See Use Client/Server Access to Post Office in Chapter 3: Reconfigure the POA in Book 2: Post Office Agent in the Agent Configuration Guide. Possible Cause: The SSL certificate has been damaged. get redirected here fix Referred to TIDs Performance, Tuning and Optimization 2943356 and 2943472Physical Packet Receive BuffersReceive buffers are used to store incoming packets from each of the networks attached to a NetWare server.

On the other hand, if your server memory load is very high and you receive frequent ECB allocation errors, you should probably set your maximum ECB allocation higher. Check the IP address for the POA. Exit the Link Configuration tool and save your changes9.

ExplanationTCP/IP load failed because a required file was missing.

Action: Correctly configure TCP/IP on the server. For example, two GroupWise agents might be running on the same server where both were configured for the same port. ExplanationConnection was broken while in use. It is possible that TCP/IP is loaded incorrectly on this machine.

Possible Cause: A client or server machine has crashed, or the process was forced to close without shutting down. Check for a SET command at DOS that is providing an incorrect path to the post office. Possible Cause(s)If this error occurs when the user starts the 16-bit GroupWise client, the client may be starting with an incorrect /ph setting. useful reference Action: See 8901 Cannot use TCP/IP services. 8908 Cannot connect to specified address Source: GroupWise engine; TCP/IP communication.

See Server Certificates and SSL Encryption in Security Administration in the GroupWise 2012 Administration Guide. 8921 SSL accept failure Source: GroupWise engine; TCP/IP communication. Explanation: You have configured an agent for SSL, but the agent cannot read the private key file or the password. Provide Feedback © Micro Focus Careers Legal close Feedback Print Full Simple Request a Call Follow Us Facebook YouTube Twitter LinkedIn Newsletter Subscription RSS 8xxx DNS is not loaded and you are trying to resolve DNS names.

If not, change the IP address and press ESC key andselect Yes to save the changes.Type "edit hosts" at the System Console and press Enter.Scroll at the bottom and verify that Possible Cause: Another program was temporarily using a very large amount of memory on the machine. Action: See 8901 Cannot use TCP/IP services. 890A Cannot listen on specified port Source: GroupWise engine; TCP/IP communication. ExplanationA fundamental TCP/IP call failed.

© 2017 imagextension.com