Home > Socket Error > Ftp 550 I/o Error Socket Closed

Ftp 550 I/o Error Socket Closed

Contents

boolean remoteRetrieve(Stringfilename) Initiate a server to server file transfer. Unable to connect: Connection time out: The hostname may be incorrect or the FTP server may be behind a firewall. You must call this method before EVERY server to server transfer attempt. if you have entered something like ftp://my.hostname.com/ then change it to my.hostname.com Socket Error # 10061, Connection refused: The hostname is correct, but either the FTP server is not listening on have a peek at this web-site

BSD-compatible HOSTS, SERVICES or PROTOCOLS files) could not be found, or a DNS request was returned by the server with a severe error. Parameters:parserFactory - factory object used to create FTPFileEntryParsersSee Also:FTPFileEntryParserFactory, DefaultFTPFileEntryParserFactory disconnect public void disconnect() throws IOException Closes the connection to the FTP server and restores connection parameters to the default Imported from legacy forums. Try entering the hostname or IP address, not a URL (e.g. pop over to these guys

Ftp Socket Error

The hostname is correct, but the FTP server is not listening on the port, there is no FTP server running, or a firewall is blocking the connection.10093 - Connection failed. the log terminates after the 150 command Connected to 66.181.11.82:990 on 5/8/2007 @ 2:22:51 PM< 220 > USER aviacode< 331 Password required> PASS *****< 230-user logged in< Welcome to Imaging Service's You should keep in mind that the FTP server may choose to prematurely close a connection if the client has been idle for longer than a given time period (usually 900 When you encounter an FTPConnectionClosedException , you must disconnect the connection with disconnect() to properly clean up the system resources used by FTPClient.

Try temporarily turning off any firewall you are running.10052 - Network dropped connection on reset. in sendto. port 0). Ws_ftp Failed To Create Socket Always check that your routers firmware is up-to-date.

WSAESOCKTNOSUPPORT (10044)Socket type not supported.The support for the specified socket type does not exist in this address family. How To Fix Socket Error Verify your input; e.g., make sure there are no erroneous characters, spaces, etc. 502 Command not implemented. boolean makeDirectory(Stringpathname) Creates a new subdirectory on the FTP server in the current directory (if a relative pathname is given) or where specified (if WSASYSCALLFAILURE (OS dependent)System call failure.Returned when a system call that should never fail does.

Try switching the connection port. 10066 Directory not empty. Socket Error 11001 Host Not Found What do I do when two squares are equally valid? Active And Passive FTP Modes. Article ID: 1146 Last updated on 1/9/2014 3:32:20 AM Product: Web Hosting Tags: error, connection, ftp, mode, active, passive Many FTP connection problems are caused by intermittent network issues.

How To Fix Socket Error

Applies to Xceed FTP for .NET. See WSAENETUNREACH WSAEINPROGRESS (10036)Operation now in progress.A blocking operation is currently executing. Ftp Socket Error The solution to this error is to "try logging back in; contact your hosting provider to check if you need to increase your hosting account; try disabling the firewall on your What Is A Socket Error Are leet passwords easily crackable?

staticint ACTIVE_REMOTE_DATA_CONNECTION_MODE A constant indicating the FTP session is expecting all transfers to occur between two remote servers and that the server the client is connected to should connect to Check This Out Please note: we do not monitor these comments for support requests. You can try to connect in non passive mode. This should be one of FTP.ASCII_FILE_TYPE , FTP.IMAGE_FILE_TYPE , etc. Ftp Errors And Solutions

Where NAME is an official system name from the list in the Assigned Numbers document. 220 Service ready for new user. (Informational) 221 Service closing control connection. Code Description Discussion 100 Series The requested action was initiated; expect another reply before proceeding with a new command. 110 Restart marker reply. Options Print Article Export As PDF Find Similar CuteFTPerror codesstatus codes Customer Support Software By InstantKB 2016-3 Final Execution: 0.000. 3 queries. Source If possible, an access to your FTP server so we can analyze the communication.

Throws: IOException - If an I/O error occurs while either sending a command to the server or receiving a reply from the server. _connectAction_ Sftp Error Codes Also In This Category WebHelp not displaying properly in browser Does Globalscape have a replacement for CuteSITE Builder? Any other type of operation might also return this error - for example, setsockoptsetting SO_KEEPALIVE if the connection has been reset.

boolean isRemoteVerificationEnabled() Return whether or not verification of the remote host participating in data connections is enabled. FTPFile[] listFiles() Using the default system autodetect mechanism,

boolean completePendingCommand() There are a few FTPClient methods that do not complete the entire sequence of FTP commands to complete a transaction. For more details, see this thread. By calling shutdown a partial close of a socket is requested, which is a signal that sending or receiving or both has been discontinued. Socket Error 10061 Connection Refused if I set the timeout to a long value, then after about 11 minutes I get the IO error.

I believe this is pretty much exactly like the sample in your docs. This is because FTPClient sends a PASV command to the server only just before opening a data connection, and not when you call enterLocalPassiveMode(). WSAEINTR (10004)Interrupted function call.A blocking operation was interrupted by a call to WSACancelBlockingCall. have a peek here Insufficient storage space in system 106 500=500 ;;Syntax error, command unrecognized 107 501=501 ;;Syntax error in parameters or arguments 108 502=502 ;;Command not implemented 109 503=503 ;;Bad sequence of commands 110

Ask FTP administrator to increase allotted storage space, or archive/delete remote files. 500 Series The command was not accepted and the requested action did not take place. 500 Syntax error, command Where NAME is an official system name from the list in the Assigned Numbers document. 220 Service ready for new user. 221 Service closing control connection. 225 Data connection open; no This method issues a PORT command to the server, indicating the other server and port to which it should connect for data transfers.

© 2017 imagextension.com